.png)
After-sales service works when every unit you sell becomes a record with its serial number, customer, site, warranty and contract. Every request then comes in through one front door, gets checked as warranty or billable at the start, and ends with proof of the work done. Offer a service contract before the warranty runs out, and the customer has a reason to stay.
Selling the machine is the easy part. The hard part starts when it stops working at 4:55pm on a Friday and the customer rings you, not the manufacturer. They don’t care whose name is on the nameplate. They care who is coming to fix it, and when.
This guide walks through how equipment distributors can run after-sales service so that the answer to “who’s coming, and when?” is never “let me check”.
It starts the day the equipment is delivered and runs for as long as the customer owns it. For most distributors it covers:
Manufacturers’ own service lists look much the same: inspections, commissioning, repairs, service contracts, parts and on-site training. What changes for a distributor is where the money and the paperwork sit, and we’ll get to that.
Because it tends to be where the profit is. Deloitte puts the average operating margin from aftermarket services at about 2.5 times the margin on new equipment sales. A McKinsey analysis across 30 industries found aftermarket margins of 25 percent, against 10 percent for new equipment.
A fair warning: those figures describe manufacturers, not distributors, and they aren’t brand new. Treat them as a direction of travel, not a promise. Your own numbers will differ.
There’s also a softer reason. Nobody remembers the sales pitch, but everybody remembers the week the machine sat broken. How you handle that week decides whether you get the next order.
You’re in the middle. You promise the customer a fix, but the manufacturer decides what it will pay for, and on which paperwork. That gap is where money quietly leaks away.
Manufacturers usually want proof before they reimburse a claim. One engine maker, for example, asks for proof of purchase and installation, the original work order and the engine’s serial number. One heating and cooling distributor’s training notes warn that a part may not count as warranty if the equipment was never registered, or if the person claiming isn’t the original owner.
Deadlines and documents vary from one manufacturer to the next, and some deadlines are short. So the first job is to read each manufacturer’s warranty terms and write down what they ask for. Warranty, consumer-protection and right-to-repair rules also differ from country to country, so check what applies where you sell.
Start with a simple record for each machine:
Without this, every service call begins with detective work. Which unit is it? When did we install it? Is it still covered? Some field service guides describe the result as digging through old records before every single visit, which is exactly as slow as it sounds.
Capture the details at delivery or installation, while the machine is in front of you. Registering the unit with the manufacturer matters too, because an unregistered machine can complicate a claim later.
Through one front door. If requests arrive by WhatsApp, phone calls, emails and the occasional shout across the showroom, nobody can say what’s open, who owns it, or how long it has been waiting.
Better options are a QR code on the machine itself, a customer portal, or a single number that feeds one system. A QR code is especially handy, because the request arrives already tied to the right unit.
A request that already knows the model, the serial number and the history saves that first, slightly painful phone call: “Which machine is it, and where is it?”
Read How to Replace WhatsApp Fault Reporting with QR Codes
Decide at the start, when the job is created. That prevents two expensive mistakes: billing a customer for work that was covered, and absorbing the cost of work that wasn’t.
A simple check:
That last one is worth a flag. A fault that keeps returning deserves a closer look before the next visit, and sometimes a conversation with the manufacturer.
First-time fix means solving the problem on the first visit, without a return trip. Three things drive it, and all three are settled before the technician leaves the workshop:
Remember: first-time fix on its own doesn’t tell you whether service is good. A technician who closes jobs quickly and leaves half of them to bounce back looks great on paper and terrible to customers.
A finished job should leave a trail anyone can follow:
Distributors have one extra wrinkle. A single job may need a report for the customer, another set of documents for the manufacturer’s warranty claim, and sometimes a template your biggest customer insists on. Keep all of them attached to the same job. When one job’s paperwork is scattered across three folders, one of the three goes missing, and it’s always the one the manufacturer asks for.
Offer the contract before the warranty ends, not after. The best moment is a few months before expiry, while the customer still remembers how smoothly (you hope) the last visit went. Put a date in the diary for each unit.
A couple of terms worth knowing:
Link each contract to a maintenance schedule so that visits are created automatically and nobody has to remember them. Then keep an eye on the things that tell you whether the contract is healthy: renewal rate, on-time visits and the margin on the agreement.
Keep the list short enough that someone actually looks at it:
Field service people also talk about “leakage”. Warranty leakage is money you could have recovered from the manufacturer but didn’t. Contract leakage is similar: service you deliver under a contract that isn’t tracked or billed properly. Both are quiet, and both add up.
You don’t need to do all eight at once. Steps 1 to 3 alone will make an immediate difference.
A spreadsheet is fine for a handful of machines and one very organized person. It struggles when there are more customers, more technicians, or more than one person updating it, and it can’t remind anyone about anything. If you have a tab for every customer and a different version on every manager’s laptop, you’ve probably reached that point.
Whatever you use, look for:
FieldEx is field service and maintenance software that equipment distributors use to run after-sales service without spreadsheets or lost paperwork. Every unit you sell becomes a permanent record, connecting commercial sales to field execution:
Two of our customers show how this works in practice. A foodservice equipment supplier in Southeast Asia runs installations, maintenance and repairs for 90+ technicians in one system. Jobs are matched to technicians by region, skills, equipment brand and model, and the customer and warranty documents for each job are kept together. Coffex, a coffee roaster and machine distributor, replaced paper service reports with mobile reports that customers sign on the technician’s phone.
Read the foodservice equipment supplier story | Read the Coffex story
You can try FieldEx free for 14 days, no credit card needed, or book a demo and we’ll set up a sample of your installed equipment with you.
Installation, training, warranty handling, planned maintenance, repairs, spare parts and service contracts. For a distributor it also includes the paperwork with the manufacturer, which is easy to forget until a claim is due.
Keep a record for every unit (serial number, installation date, proof of purchase) and the original work order for every repair. Check each manufacturer’s terms and deadlines, and submit promptly with the documents they ask for.
Give each unit its own record with its serial number, customer, site, warranty and contract. In FieldEx, every unit you sell becomes an asset linked to its customer, site, sales orders and contracts, with warranty details on the record and every job added to its history.
Industry averages sit in the high 70s percent, and best-in-class teams are near 88 percent. Track it alongside your repeat-visit rate, so you can tell quick jobs from finished ones.
Offer the contract a few months before the warranty ends, tie it to a maintenance schedule, and follow up on every renewal. Track attach rate and renewal rate so you can see what’s working.
It depends on your agreement. Many distributors handle installation and first-line service themselves, and go to the manufacturer for parts and warranty reimbursement. Check your distribution agreement so you know who does what, and who pays.
Software that keeps the installed equipment, warranties, contracts and service jobs together. FieldEx is built for this. Planned servicing can run by calendar, by meter reading or by whichever comes first, and it starts automatically when a new unit matches a plan. Customers can see their equipment and raise requests in a portal, and the office is alerted when a new job repeats a recent job on the same unit.
