.png)
Stick a QR code on the equipment tenants most often report problems with, such as a lift, an aircon unit or a pump room door. A tenant scans it with their phone camera and fills in a short form. They don’t need an app or an account. The report arrives in your maintenance system as a job, gets passed to the right team automatically, and leaves a record of what was done and when.
If your building’s fault reporting currently lives in a WhatsApp group, you probably know how this goes. A tenant sends “the lift is making a noise again” at 8.47pm. Somebody reacts with a thumbs up. Nobody is sure whether that means “I’ll handle it” or “I saw this and am now ignoring it.” Three days later the lift is still noisy and the group chat has moved on to a heated debate about parking.
Nobody is doing a bad job here. WhatsApp was built for chatting with friends, not for running a building. So let’s look at what goes wrong, and how a QR code can fix it without making life harder for your tenants.
It works fine until it doesn’t, and it usually stops working at the exact moment you need it most. A few things tend to go wrong:
That last one matters more than people expect. A building’s repair history is hard to rebuild once it’s scattered across phones.
Think of it as a “report a problem” button, printed on a sticker and attached to the thing that might break. The QR code is linked to that specific piece of equipment. Whoever scans it gets a short form, and whatever they submit becomes a proper job with a clear owner.
The tenant doesn’t need to know who to message, which group to post in, or whose number to use this month. They just scan, describe the problem and send.
Setting this up is simpler than it sounds. Here’s the whole journey:
No chasing, no forwarding, and nobody playing detective with a vague message.
A good rule is one code for each thing that can break and that people can reasonably report on. Some obvious places to start:
Because each code is tied to a specific item, the report arrives already knowing what it’s about. That’s the quiet superpower here. You’ll never again have to reply “which lift?”
It’s worth spending a little time up front deciding what counts as its own item, and the rest mostly takes care of itself.
Let’s follow one fault from start to finish. A tenant notices the lobby aircon dripping onto the floor.
Why the history matters: if it drips again in three months, you’ll see the pattern straight away. That makes it much easier to decide when something needs replacing instead of patched up for the fourth time.
Alerts for urgent faults: managers can set up alerts so the right person hears about certain jobs immediately. A water leak, for example, probably shouldn’t wait for someone to check the list.
It suits anyone who looks after buildings and takes fault reports from other people. You’ll feel the difference most if you are:
Got several buildings? It’s especially handy. Every site reports the same way and shows up in one place, instead of one WhatsApp group per building and one very tired person watching all of them.
FieldEx is a field service and maintenance management system, and the QR code reporting described above is built in. Every piece of equipment can have its own QR code, an admin can switch on a public form so anyone can report a fault without an account, and each report arrives as a job assigned to your team, with the full history saved against the equipment.
Royal Facilities Management uses QR codes at every client site so tenants and site staff can report faults in seconds, with no app or login. See how they run their Oman contracts on FieldEx.
You can try FieldEx free for 14 days, no credit card needed, or book a demo and we’ll walk you through it with your own buildings in mind.
Not if the form is public. Tenants scan the code with their phone camera and fill in a short form, with no app, no account and no login. Not every maintenance system works this way, though. Some ask tenants to log in or install an app, so check that the form can be made public before you commit. In FieldEx, an admin switches on a public form for each QR code, so anyone can report a fault without an account.
In FieldEx, it becomes a job of a type you’ve chosen in advance and is assigned to your team automatically. The technician is notified, does the work, and the result is saved to that equipment’s history.
Yes. Each code is tied to one item, so you can cover anything from a lift to a water pump, and each report arrives knowing exactly what it’s about.
In FieldEx, jobs go to a team and are shared out evenly among its members. Anyone on approved leave is skipped, so a report doesn’t land with someone who’s on a beach.
Of course. QR codes are best for everyday faults. A burst pipe at 2am still deserves a phone call, and plenty of teams keep a call or message route for genuine emergencies while routine reports go through the QR code.
Yes. Reports from every site come into the same FieldEx system, so you can see what’s open across all your buildings in one place.
